HP Laserjet 1300t Toner Cartridges

The HP LaserJet 1300T claims a reasonably small footprint that can easily fit on a standard-sized desktop or office table, measuring 9.5 inches tall, 19.1 inches deep, and 16.3 inches wide. It is built with a monochromatic laser engine that can print with a resolution of up to 1200dpi. The device runs on 16MB of standard memory. This printer offers a total maximum sheet capacity of 510 sheets. The HP 1300T laser printer connects to a PC or Mac computer via a parallel or USB interface. The Laserjet 1300T only uses black HP Laserjet 1300t Toner Cartridge.

A small workgroup can share the HP LaserJet 1300T mono laser printer with an Ethernet network interface and to avoid compromising speed, the users can upgrade the memory. The printer is notably fast and produces prints at speeds of up to 19ppm, making it time-saving. The LaserJet 1300T is also compact, so it doesn't demand a lot of installation space and you install it in a smaller place. The LaserJet 1300T is compatible with most major operating systems. HP provides drivers for Windows 95 and later, Mac OS X and later, Novell NetWare, Red Hat Linux, SuSE Linux, HP-UX, Solaris, IBM AIX and MPE-iX.

• High capacity HP Laserjet 1300t Toner Cartridge
• Ethernet Networking
• Fast speed
• Compact machine

• Bulky, weighs 8.61 kg
• Sub-par print quality

The cartridge compatible with HP Laserjet 1300t printer is:

• HP Q2613A Black Toner Cartridge

This 8.61 kg bulky HP LaserJet 1300T machine is known as a high-performance monochrome laser printer for busy professionals with a small or home office. Along with easy expansion options to fulfil the needs of a growing business and multiple users, the LaserJet 1300T printer comes with a network-friendly interface, too. The Laserjet 1300T only uses black HP Laserjet 1300t Toner Cartridge which can be replaced when out of ink, making it cost-effective.

How to get rid of an ‘Out of Paper’ error while using HP Laserjet 1300t Toner Cartridges?

Perform the following instructions in the given order. Use the printer after each task to check if the issue is resolved.

• Check the paper stack for defects such as wrinkled, torn or bent pieces that might have caused the pick-up issue.
• Remove any paper from the paper tray.
• Pull out if any severely bent, wrinkled or torn paper found in the stack.
• Check for obstructions inside the paper tray. Make sure that nothing stops the paper from engaging with the rollers.
• Ensure that the paper stack is even on all sides.
• Load the stack of paper in the paper tray.
• Close or push in the paper tray.
• Select the proper paper size on the printer control panel or in the printer software.

Clean the paper pick rollers under the HP Laserjet 1300t Toner Cartridges or inside the paper tray area.

• Get a flashlight.
• Turn off the printer.
• Wait for the printer to the idle state and then disconnect the power cord and any cables from the rear of the printer.
• Remove any stack of paper from the input tray.
• Use a flashlight to find the paper pick rollers.
• Lightly dampen a cotton swab with water, and then squeeze it to remove any spare water.
• Clean the rollers with a swab by rotating them with your fingers.
• Allow the rollers to dry for two minutes.
• Reconnect the power cords, and cables and then turn on the printer.

Note: Do not touch the electrical contacts near the HP Laserjet 1300t Toner Cartridges.

Reset the printer to recover from print errors and failures.

• Disconnect the power cord from the printer with the printer turned on.
• Unplug the power cord from the power source.
• Wait for 60 seconds and then reconnect the power cords to the wall outlet and the printer.
• Turn on the printer to complete the reset.